| Filename | Latest commit message | Latest commit date |
|---|---|---|
Felipe M.
590228388c
Replace the corner-cylinder hull in back_plate() with a hull of rotate_extruded posts whose top-right 2D corner is filleted, so the back plate's front-face perimeter rounds smoothly into the side walls while the back face stays flat against the pegboard. Adds the back_front_fillet_r parameter (default 1.0 mm). |
||
| .. | ||
| holder.scad | ||
| holder.stl | ||
| preview.png | ||
| README.md | ||
Skadis Coffee Tamper Holder
IKEA Skadis pegboard holder for a coffee tamper that ships in a tamper cup (designed around a Normcore 58mm tamper inside its 64mm cup). The cup drops open-end-up into the holder's pocket; the tamper rests on top of the cup with its tamping face protected.
Mounting (T-Clip system)
Mounts to the Skadis pegboard via the
T-Clip system from Printables #256896.
The slot + recess geometry is provided by
lib/skadis-t-clip, which the holder consumes
via use <../lib/skadis-t-clip/skadis-t-clip.scad>. The narrow upper
section carries a single Skadis-pattern pill-shaped through-slot
surrounded by a circular recess that seats the printed clip's cap.
Print the clip separately and use it like this:
- Hold the holder against the pegboard so the slot lines up with a pegboard slot.
- Push the clip's stem through both slots (clip's long axis parallel to the slot, i.e. vertical).
- Twist the clip 90 degrees — the cap is now perpendicular to the slot and sits flush in the recess, locking the holder in place.
The cup pocket itself is wide and prevents rotation around the single
mount point. Set mount_count = 2 if you want a second slot 40mm above
for additional restraint.
Print orientation
Print upright (Z up, back plate vertical, cup pocket axis vertical). The pocket floor sits flat on the bed and all walls print as vertical extrusions. A brim helps with the small footprint.
Parameters
Tamper Cup
| Parameter | Default | Description |
|---|---|---|
cup_diameter |
64 mm | Outer diameter of the tamper cup |
cup_pocket_depth |
10 mm | How far the cup sits in the holder |
cup_tolerance |
0.4 mm | Radial clearance around the cup, per side |
cup_floor |
4 mm | Pocket floor thickness (0 = open bottom) |
cup_drain_diameter |
50 mm | Drainage / pass-through hole in the floor (0 = solid) |
cup_front_cut_width |
30 mm | Front-cut window so the cup is graspable (0 = closed) |
Holder Body
| Parameter | Default | Description |
|---|---|---|
pocket_wall |
4 mm | Wall thickness around the cup pocket |
merge_overlap |
3 mm | Overlap between cup pocket and back plate at the merge plane |
Skadis Mount
| Parameter | Default | Description |
|---|---|---|
mount_count |
1 | Number of slot rows (1 = compact; 2 prevents rotation under heavy loads) |
mount_pitch |
40 mm | Vertical pitch between slots (Skadis standard) |
back_thickness |
5.4 mm | Back-plate thickness at the thickest part (the rim around the recess); thinnest = back_thickness − clip_recess_depth |
back_margin |
6 mm | Margin around the slot recess on the back plate |
back_corner_r |
4 mm | Outer corner radius of the back plate |
Skadis Slot
| Parameter | Default | Description |
|---|---|---|
skadis_slot_width |
5.0 mm | Pill-slot width (Skadis nominal 5 mm) |
skadis_slot_height |
15.0 mm | Pill-slot length (Skadis nominal 15 mm) |
clip_recess_diameter |
22.2 mm | Cylindrical recess diameter on the front face |
clip_recess_depth |
2.9 mm | Recess depth; thinnest wall at the slot = back_thickness − clip_recess_depth |